Skip to content
jtrevino@trecasa.com.mx
TRECA Troquelado y estampado

12, 13 or 14 gauge: which steel to choose for an air tank

By the TRECA engineering team · Updated · 5 min read

In steel sheet, 12 gauge is 0.1046 in (2.66 mm), 13 gauge is 0.0897 in (2.28 mm) and 14 gauge is 0.0747 in (1.90 mm). The lower the number, the thicker and heavier the steel: 12 gauge gives more margin against corrosion and impacts, while 14 gauge saves weight and cost.

Thickness and weight by gauge

Manufacturers' standard gauge values for carbon steel sheet. Weight is for bare steel, without coating.

Thickness and weight of 12, 13 and 14 gauge steel sheet
GaugeThickness (in)Thickness (mm)Weight (lb/ft²)Weight (kg/m²)
12 gauge0.10462.664.37521.4
13 gauge0.08972.283.75018.3
14 gauge0.07471.903.12515.3

Going from 14 gauge to 12 gauge adds 40% to the thickness and weight of the steel.

Approximate tank weight by gauge

Weight of the shell and both heads, calculated from the tank's surface area. It does not include couplings, brackets, welds or paint, so the finished tank weighs a little more.

Size (L × D)12 ga13 ga14 ga
17 1/2 × 9 1/2 in20.2 lb (9.2 kg)17.3 lb (7.8 kg)14.4 lb (6.5 kg)
24 1/2 × 9 1/2 in26.5 lb (12.0 kg)22.7 lb (10.3 kg)18.9 lb (8.6 kg)
30 1/2 × 9 1/2 in32.0 lb (14.5 kg)27.4 lb (12.4 kg)22.8 lb (10.4 kg)
27 3/4 × 10 in31.3 lb (14.2 kg)26.8 lb (12.2 kg)22.3 lb (10.1 kg)
42 × 10 in44.9 lb (20.3 kg)38.5 lb (17.4 kg)32.0 lb (14.5 kg)
28 1/2 × 12 in39.5 lb (17.9 kg)33.9 lb (15.4 kg)28.2 lb (12.8 kg)

When each gauge makes sense

12 gauge

The thickest of the three. It gives more margin against corrosion, rock strikes and wear at the mounting brackets, at the cost of more weight. It is the usual choice for tractor tanks and for units that run in mud, road salt or humidity.

13 gauge

A middle ground: it cuts the steel weight by about 14% compared with 12 gauge and keeps good stiffness on 9 1/2 inch diameters.

14 gauge

The lightest steel, about 29% less weight than 12 gauge. It is considered when weight or cost matter most, on small-diameter tanks and less exposed applications.

In every case, the gauge must suit the system's working pressure and the vehicle or trailer manufacturer's specification. When replacing a tank, the safest choice is to match the original gauge; the guide to measuring a tank explains how to check it with a caliper.

How to find the gauge of a tank you already have

  1. Look for the label or part number: the gauge is often on the spec sheet.
  2. Measure the thickness with a caliper at an accessible edge, for example next to a coupling, and compare it with the table. Remove the paint at that spot first.
  3. If the steel falls between two values, take the closest one: 2.6 mm (0.102 in) is 12 gauge and 1.9 mm (0.075 in) is 14 gauge.

Have your size and gauge? Get a quote for your tank here.

Gauge questions

The questions fleets, repair shops and truck body builders ask us most.

How thick is 12 gauge steel?

12 gauge steel sheet is 0.1046 inches, or 2.66 mm. 13 gauge is 0.0897 in (2.28 mm) and 14 gauge is 0.0747 in (1.90 mm).

What gauge does TRECA use for its air tanks?

TRECA standard tanks are made of 12 gauge steel. Some 9 1/2 inch diameter sizes are also offered in 13 or 14 gauge. All of them pass a leak test at 125 psi.

Is a higher gauge number thicker?

No, it is the other way around: the higher the number, the thinner the steel. 14 gauge is thinner than 12 gauge.